Logitrans SELFSR 1003 Fully Powered Rotator with Straddle Legs and Non-Adjustable Box Holders

The Logitrans SELFSR 1003 is the final configuration in the Logitrans rotator range, combining fully powered operation (electric lift and electric drive) with a straddle leg design and non-adjustable box holders. It is built for operations that handle a consistent, standardized box size across all pallet types, including closed-bottom pallets, and involve frequent travel between workstations throughout the shift.

The straddle legs extend on either side of the pallet base, allowing the SELFSR 1003 to engage all pallet types without requiring entry pockets on the underside. The fixed box holders engage quickly and without adjustment, reducing cycle time in high-repetition environments. Powered drive eliminates manual pushing effort during transport. The unit tilts loads beyond 90 degrees while maintaining a 2,200 lb rated capacity.

Two fork width options are available (22" and 27"). Five models cover lift heights from 36" to 75", all sharing the same fork length and 2,200 lb capacity. Prices are listed by manufacturer model number for easy comparison with competitors.

Straddle Leg Design -- Pallet Compatibility:

The SELFSR 1003 uses a straddle leg design, meaning the outrigger legs straddle the outside of the pallet base. This allows it to handle all pallet types, including closed-bottom pallets, block pallets, and standard four-way entry pallets. The pallet compatibility image on this page shows supported configurations.

Where the SELFSR 1003 Fits in the Full Rotator Range:

All six Logitrans rotator configurations share the same fork dimensions (22" or 27" wide x 49" long), lift height range (36" to 75"), and 2,200 lb capacity. Here is where the SELFSR 1003 sits in the range:

♦ Non-Adjustable Holders, Powered Lift, Manual Push, Fork-Over: ELFR 1001. Lowest price.
♦ Non-Adjustable Holders, Powered Lift, Manual Push, Straddle Legs: ELFSR 1001. All pallet types, manual push.
♦ Non-Adjustable Holders, Powered Lift, Powered Drive, Fork-Over: SELFR 1002. Standard pallets, powered drive.
♦ Non-Adjustable Holders, Powered Lift, Powered Drive, Straddle Legs: SELFSR 1003 (this page). All pallet types, powered drive. Highest price among non-adjustable models.
♦ Adjustable Holders (31.5" to 48"), Powered Lift, Powered Drive, Fork-Over: SELFRA 1002.
♦ Adjustable Holders (31.5" to 48"), Powered Lift, Powered Drive, Straddle Legs: SELFSRA 1002. Highest price overall.

The SELFSR 1003 is the correct choice when your box dimensions are consistent, your operation handles closed-bottom or mixed pallet types, and operators need powered drive for frequent travel between stations. If any of those three conditions do not apply, a lower-priced configuration is likely the better fit. Contact us at 866-333-0728 or use the quote form to confirm.

Choosing the Right Lift Height:

All five SELFSR 1003 models carry 2,200 lbs to their full rated height. Select based on the working height that best fits your operators and workstations.

♦ SELFSR 1003-36 -- 36" maximum lift height. Floor to standard work surface.
♦ SELFSR 1003-47 -- 47" maximum lift height. Mid-height access for elevated workbenches or conveyor infeed.
♦ SELFSR 1003-55 -- 55" maximum lift height. Upper mid-height for taller workstations or elevated staging.
♦ SELFSR 1003-63 -- 63" maximum lift height. Tall workstations or rotation access above standard height.
♦ SELFSR 1003-75 -- 75" maximum lift height. Maximum reach. Best for overhead conveyors or elevated discharge points.

Not sure which height fits your workstation setup? Call 866-333-0728 or use the quote form.