Husky 42x192 Add-On Pallet Racking Section, SU29 13 Gauge Frame

A Husky 42x192 SU29 add-on pallet racking section is the bay that extends an existing row of Husky teardrop pallet rack built on SU29 frames: it ships with one SU29420192 welded upright frame measuring 42 inches deep by 192 inches high, three or four pairs of Husky IBX, IBN or IBH step beams, and the Bowlock clips that lock each beam to the frame. An add-on has one frame instead of two because it bolts its beams to the open side of the frame already standing at the end of the row, so each add-on shares a frame with its neighbor. A row of five bays is one starter section plus four add-ons, and every add-on must match the depth, height and column of the starter it joins. This add-on is for rows built on the SU29 frame; the same 42x192 add-on is sold separately on the standard IU18 frame and the 14 gauge heavy duty IU24 frame.
Add-on unit, extends an existing rowUS made high strength steel, ASTM A1011-GR55 Usually ships in 3-4 days
The SU29 frame is the heaviest of the three 42x192 frames CustomMHS sells. Its columns are 3 inch by 3 inch steel tubing in 13 gauge, one gauge thicker than the 14 gauge 3 by 3 inch IU24 column and a different shape entirely from the 3 by 1-5/8 inch IU18 column. Each upright adds 3 inches to the overall row length. Teardrop punching on 2 inch centers lets beam levels adjust in 2 inch steps. Frames are finished green and beams orange. On a 16 foot frame that carries three or four loaded levels from two bays and takes forklift contact at the base for years, the thicker column is what the shopper is paying for. Each beam pair is rated separately, and the beam rating, not the frame rating, is normally what limits how much goes on a single level. The capacities in the table below are per pair of beams, evenly distributed across both beams.
The 42 inch frame depth is sized for standard 48 inch GMA pallets, which overhang the front and rear beams by three inches on each side by design. Four levels on a 192 inch frame puts beams roughly 46 inches apart; three levels spreads them to about 62 inches. A 192 inch frame on a 42 inch base has a height to depth ratio of about 4.6 to 1, under the 6 to 1 point where row spacers or overhead ties are required, and placing a pallet on the top beam at roughly 15 feet calls for a reach truck rated for that height. Wire decking lays across the two beams of a level to support cartons, drums and odd-sized loads and lets sprinkler water pass through; on the decked models each deck is 42 inches deep and rated 2,600 pounds. Add-ons are offered in 48, 96, 108, 120 and 144 inch bay widths so a row can mix widths as long as every bay shares the same frame: a 96 inch bay holds two 40 inch wide pallets, a 108 inch bay holds two 48 inch pallets, a 144 inch bay holds three 40 inch pallets.
Product Lines:
All add-ons in this category share the Husky SU29420192 frame, so the model number changes only by beam, level count and decking. Read SU29420192-IBN55108-4AW left to right: SU29 marks the 3 by 3 inch 13 gauge welded upright, 420192 is the 42 inch deep by 192 inch high frame, IBN55108 is a 5-1/2 inch tall step beam 108 inches long, 4A means four beam levels in an add-on section (3A means three; a starter would read 4S or 3S), and a W on the end means wire decking is included. IBX beams are the standard Husky step beam, IBN beams are the heavier 5-1/2 inch profile, and the IBH60144 is a 6 inch beam for the heaviest 144 inch spans.
Per pair beam capacities by bay width: 48 inch bays use the IBX30048 beam rated 7,383 pounds. 96 inch bays use the IBX35096 at 4,044 pounds, the IBX39096 at 5,047 pounds, or the IBX43096 at 6,111 pounds. 108 inch bays use the IBX43108 at 5,000 pounds or the IBN55108 at 8,873 pounds. 120 inch bays use the IBX43120 at 4,062 pounds. 144 inch bays use the IBX43144 at 3,000 pounds, the IBN55144 at 5,569 pounds, or the IBH60144 at 7,820 pounds. Every beam is offered in three or four levels, with wire decking (AW) or without (A); the IBH60144 add-ons are currently listed without decking only.
Selecting the Right Model:
◆ Match the frame code first. An SU29 add-on joins an SU29 starter; if your row was built on IU18 or IU24 frames, buy the add-on from that page instead. The frame number before the first hyphen (SU29420192) and the level count (3A or 4A) should both match the starter.
◆ Count bays, not frames. A row of N bays needs one starter and N minus 1 add-ons. Buying a starter for every bay wastes a frame per bay and adds 3 inches of width each time.
◆ Ask for the SU29420192 frame rating at your beam spacing before loading heavy beams on both sides of a shared frame. Frame ratings are published at a stated beam spacing and fall as levels spread apart, and a shared frame carries half the load from every level on both sides.
◆ Start with the heaviest pallet you will store, double it for a two-pallet bay or triple it for a three-pallet bay, and pick a beam pair rated above that total. The beam rating is per pair and assumes the load is spread evenly across both beams.
◆ Choose bay width by pallets per level. A 96 inch bay fits two 40 inch pallets, a 108 inch bay fits two 48 inch pallets, and a 144 inch bay fits three 40 inch pallets, each with about 4 inches of clearance. Widths can vary down a row as long as the frame is the same.
◆ Add wire decking (the AW models) if you will ever place cartons, drums or loose items on the rack, or if your fire code or insurer asks for open decking under sprinklers. Wire decking does not raise the beam capacity.
What does SU29 mean on a Husky pallet rack frame?
SU29 is the frame code on Husky’s 3 by 3 inch, 13 gauge welded upright, the heaviest of the three columns CustomMHS sells for 42 inch deep rack; IU18 is the standard 3 by 1-5/8 inch 14 gauge column and IU24 is the 3 by 3 inch 14 gauge heavy duty column. All three use the same teardrop pattern, the same Husky beams rated 3,000 to 8,873 pounds per pair, and the same Bowlock clips, so the beam capacity per level does not change; what changes is how much total weight the frame carries, how it holds up to forklift impact, and which add-on you must buy to extend the row. An SU29420192 add-on ships with one 42 inch deep, 192 inch high SU29 frame and three or four beam pairs. The CustomMHS pallet racking guide explains why every capacity has a condition attached (guide section 1), how frames, beams and bays share load in a row (section 2), the difference between roll-formed and structural columns (section 4), the 6 to 1 height to depth rule (section 6), anchoring and load plaques (section 7 and section 8), and how to inspect existing frames before extending them (section 11).
Where Commonly Used:
Husky SU29 42x192 add-on pallet rack sections are used to extend existing rows of Husky SU29 rack in distribution centers, beverage and paper warehouses, metal stock rooms and building material operations with 18 foot or higher clear ceilings where heavy pallets are stacked four high and forklift traffic at the rack face is constant.
CustomMHS carries the full line of Husky pallet rack, backed by the manufacturer’s warranty.