Lift Products Guardian Series U-Lift Low Profile Scissor Lift Tables

The Lift Products Guardian Series U-Lift is a low profile electric hydraulic scissor lift table with a U shaped platform. A 21" wide manual or electric pallet truck drives into the open center of the U, sets the pallet down on the two platform rails and backs out, so no loading ramp is needed. Lift Products says this suits wire baskets, containers and open bottom plastic or wooden pallets, where the forks must pass through the center of the platform.
Get a Fast Quote →Read our Buying Guide →
Prices are shown by manufacturer model number.
Compare the exact same item across competitors - no extra searching.
| Model Number | Platform Size | Travel | Capacity | Price | View Model |
|
44-7/8" wide x 56" long
|
3-1/8" to 33-7/8"
|
2,200 pounds
|
$5,933.15
|
||
|
45-5/8" wide x 59-7/8" long
|
3-5/8" to 33-1/8"
|
3,300 pounds
|
$7,538.89
|
The LPBLU-20 (2,200 lb) lowers to 3-1/8" and the LPBLU-30 (3,300 lb) lowers to 3-5/8". Both are well under the seven inches the CustomMHS lift table guide gives as the limit for pallet jack loading, and Lift Products says the low profile design removes the need for a loading ramp or a floor pit.
The U-Lift carries the Guardian safety features. A safety perimeter around the platform stops the descent on contact, with a reset button in the 24 V control box. A check valve stops the table from lowering if a hose bursts, a relief valve protects against overloading, a compensated flow valve controls lowering speed, an upper limit switch stops travel at the top, and there is clearance between the scissors to prevent trapping. Mechanical blocks are built in for maintenance, and the pivot points use self-lubricating bushings. The external power pack comes with 8 ft hoses and runs on 115 V single phase as standard, with 230/460 V three phase available. Options are foot controls and a stainless galvanized version. Lift Products states the series meets and exceeds both U.S. (ANSI) and EU safety standards.
Product Lines
The U-Lift comes in two models. The LPBLU-20 is rated 2,200 lb, lowers to 3-1/8" and raises to 33-7/8" on a 56" long platform with 30-3/4" of travel. The LPBLU-30 is rated 3,300 lb, lowers to 3-5/8" and has a 45-5/8" x 59-7/8" platform with 29-1/2" of travel. Both are built for a 21" wide pallet jack.
Selecting the Right Model
◆ LPBLU-20 (2,200 lb): 56" long U platform, 3-1/8" lowered, 33-7/8" raised, 42" x 52" base frame, 18 second lift.
◆ LPBLU-30 (3,300 lb): 45-5/8" x 59-7/8" U platform, 3-5/8" lowered, 43" x 56-1/4" base frame, 25 second lift.
◆ Pallet jack: Both models are designed for a 21" wide manual or electric pallet truck.
Can a pallet jack load a U-Lift table without a ramp?
Yes. A 21" wide pallet jack drives into the open center of the U, and both models lower to less than four inches, far under the seven inch limit for pallet jack loading.
See how lowered height controls loading in the CustomMHS lift table guide.
Where Commonly Used
U-Lift tables are commonly used where wire baskets, open bottom containers and pallets are brought in by pallet jack and raised to working height for loading, unloading or de-palletizing.
CustomMHS carries the full line of Lift Products Guardian Series U-Lift low profile scissor lift tables, backed by the manufacturer’s warranty.