Pallet Rack Components: Uprights, Step Beams, Decking and Accessories
Pallet rack components are the individual parts that make up a teardrop pallet rack bay, sold separately so a shopper can build a section from scratch, replace a damaged part, add a level to an existing row, or fit the safety hardware that most fire codes and rack inspections call for. A complete bay needs two upright frames, two beams per level, and the clips that lock each beam to the frame; everything else on this page (decking, crossbars, flue spacers, post protectors, row spacers, wall ties, backing and doors) is added for safety, for the type of load, or to meet a code requirement. The components here fit Husky Invincible teardrop rack with slots punched on 2 inch centers.
Get a Fast Quote →Read our Racking Components Buying Guide →
![]() Husky Pallet Rack Upright Frames
|
![]() Husky Pallet Rack Step Beams
|
![]()
|
![]() WWMH Wire Decking for Step Beams
|
||||
![]() Little Giant Pallet Rack Solid Decking for Step Beams
|
![]() Little Giant Pallet Rack Perforated Decking for Step Beams
|
![]() Husky Pallet Rack Step Beam Supports
|
Worldwide Material Handling WorldStop Flue Spacer
|
||||
![]() Pallet Rack Upright Frame Protectors
|
![]() Husky Pallet Rack Row Spacers
|
![]() Husky Pallet Rack Upright Wall Ties
|
![]() Mighty Line 5S Industrial Floor Tape
|
||||
![]() WireCrafters Heavy Duty Pallet Rack Doors
|
![]()
|
![]() Pallet Rack Medium Duty Wire Backing
|
The structural parts carry the ratings. Husky upright frames come in two columns: the IU18 at 3 inches by 1-5/8 inches in 14 gauge steel, rated 18,160 pounds at 48 inch beam spacing, and the IU24 at 3 inches by 3 inches in 14 gauge, rated 25,390 pounds at the same spacing. Husky step beams are rated per pair, from 3,000 pounds for a 4-3/8 inch tall beam at 144 inches to 8,873 pounds for a 5-1/2 inch beam at 108 inches, and the step along the top edge is what wire decking and crossbars rest in. The frame rating limits the total weight in a bay; the beam rating limits each level; and both assume the load is evenly distributed.
The rest of the page is protection and compliance. Wire decking (Husky and WWMH) lets sprinkler water pass and supports cartons, drums and odd-sized loads that would fall through open beams; Little Giant solid and perforated decking does the same for small parts, with perforated decking keeping some airflow for sprinklers. Crossbars give a pallet a bearing surface across the beam without a full deck. Row spacers and WorldStop flue spacers hold the gap between back to back rows that the fire code requires for sprinkler coverage. Post protectors take the forklift hit that would otherwise bend a column. Wall ties brace a single row to the building. Wire backing and WireCrafters rack doors keep product from being pushed off the back of a rack onto a walkway or into a locked enclosure.
Product Lines:
The tiles below run from the structure outward: frames and beams first, then decking, then the hardware that protects the rack and the people around it. Husky supplies the frames, step beams, wire decking, crossbars, row spacers, wall ties and fluted mesh backing; WWMH supplies an alternate wire deck for Husky step beams; Little Giant supplies solid and perforated steel decking; Worldwide Material Handling supplies the WorldStop flue spacer; Mighty Line supplies floor tape for aisle and rack location marking; WireCrafters supplies heavy duty wire backing, rack doors and enclosures.
Selecting the Right Model:
◆ Build the bay from the load. Pick the beam pair rated above your heaviest level, then pick the frame (IU18 or IU24) whose rating covers the sum of all levels at your beam spacing, then the frame depth that matches the pallet (42 inch for standard 48 by 40 GMA pallets, 48 inch for deeper loads).
◆ Replace like with like. A replacement frame or beam must carry the same frame code, depth and height as the rest of the row, or the row is only as strong as its weakest part and the load plaque no longer applies.
◆ Add decking by what goes on the beams. Pallets alone need no deck; cartons, drums and mixed loads need wire decking; small parts need solid or perforated decking. Solid decking blocks sprinkler water and most codes limit how much solid shelving a sprinklered rack can carry, so confirm with your fire marshal before choosing it.
◆ Keep the flue. Back to back rows need a transverse flue, typically 6 inches, held by row spacers or flue spacers so sprinkler water can reach the lower levels. Spacers are required by most manufacturers when frame height exceeds six times depth and are good practice above 16 feet regardless.
◆ Protect the column. Most rack failures start with a bent column at floor level from a forklift strike. Post protectors on aisle ends and at every tunnel bay cost far less to replace than a frame, and wall ties stop a single row from racking sideways.
◆ Back any rack that faces people. Wire backing on the rear of a rack that borders a walkway, dock door or workstation stops a pushed pallet or a loose carton from falling onto someone.
What parts do I need to build one bay of pallet rack?
One bay needs two upright frames, two beams per level (so four beams for two levels, six for three), and the beam clips, which on Husky Invincible rack are the Bowlock clips that ship with the beams; everything else is optional or code driven. Add wire decking (two decks per level on a 96 or 108 inch bay) if anything other than a full pallet will sit on the beams, anchors for every frame footplate, a load plaque for the bay, and row spacers if the bay backs onto another row. A second bay in the same row needs only one more frame plus its beams, because it shares the first bay’s end frame. Husky frames are rated 18,160 pounds (IU18) or 25,390 pounds (IU24) at 48 inch beam spacing and the beams 3,000 to 8,873 pounds per pair. The CustomMHS pallet racking guide explains why every capacity has a condition attached (guide section 1), how frames, beams and bays fit together (section 2), the 6 to 1 rule and row spacers (section 6), anchoring and load plaques (section 7 and section 8), wire decking and point loads (section 10), and how to spot column damage that calls for a replacement frame or a post protector (section 11).
Where Commonly Used:
Pallet rack components are used in warehouses, distribution centers and manufacturing plants to build new Husky teardrop rack bays, replace damaged frames and beams, add levels and decking to existing rows, and fit the flue spacers, post protectors, wall ties and backing that fire codes and rack inspections require.
CustomMHS carries the full line of Husky, WWMH, Little Giant, Worldwide Material Handling, Mighty Line and WireCrafters pallet rack components, backed by each manufacturer’s warranty.














