Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

Husky 48 Inch Deep Pallet Racking, Starter and Add-On Sections, 96 to 192 Inches Tall

Husky 48 inch deep pallet racking is a roll-formed teardrop pallet rack system built from 48 inch deep upright frames in heights of 96, 120, 144 and 192 inches, sold as starter sections with two frames and add-on sections with one frame. A 48 inch frame is the choice when the load must be supported edge to edge: a standard 48 by 40 inch GMA pallet loaded 48 inches deep sits flush with the front and rear beams instead of overhanging 3 inches each side as it does on a 42 inch frame, and pallets, crates, drums and cartons deeper than 48 inches get the full beam to beam depth under them. The trade is 6 more inches of floor per row and a slightly harder reach for the forklift operator placing a load that does not overhang. Every section on this page uses the same Husky step beams, rated per pair from 3,000 to 8,873 pounds depending on length and profile, locked to the frame with Bowlock clips on teardrop slots punched every 2 inches.kes the rear flue space easier to hold, and gives a supported footprint for deep, bulky loads. A 40" deep pallet on a 48" frame leaves a gap where product can fall, so check your load depth first. 

Get a Fast Quote →Read the Buying Guide → 

Pallet Rack Starter unit to begin each row or use as individual units
Consist of 2 uprights and shelf levels (with or without wire decking)
 Husky 48" x 96" Starter Pallet Rack.  Upright: 3" x 1-5/8", 14 gauge 8' Tall
Husky 48" x 96" Starter Pallet Rack.
Upright: 3" x 1-5/8"x 8' Tall, 14 gauge

Shop Husky 48x96 IU18 Starter Sections →
48" x 120" Starter Pallet Rack Upright: 3" x 1-5/8". 14 gauge 10' Tall
Huaky 48" x 120" Starter Pallet Rack
Upright: 3" x 1-5/8" x 10' Tall. 14 gauge

Shop Husky 48x120 IU18 Starter Sections →
 Husky 48" x 144" Starter Pallet Rack
Husky 48" x 144" Starter Pallet Rack 
Upright: 3" x 1-5/8" x 12' Tall, 14 gauge

Shop Husky 48x144 IU18 Starter Sections →

 Husky 48" x 192" Starter Pallet Rack. Upright: 3" x 3" 14 gauge 16' Tall
Husky 48" x 192" Starter Pallet Rack.
Upright: 3" x 3" x 16' Tall 14 gauge

Shop Husky 48x192 IU24 Heavy Duty Starter Sections →

 

Use add-on units to attach to the starter unit (share common upright)
Consist of 1 upright and shelf levels (with or without wire decking)
Husky 48" x 96" Add-On Pallet Rack Upright: 3" x 1-5/8", 14 gauge. 8' Tall
Husky 48" x 96" Add-On Pallet Rack
Upright: 3" x 1-5/8" x 8' Tall, 14 gauge

Shop Husky 48x96 IU18 Add-On Sections →
husky pallet rack
Husky 48" x 120" Add-On Pallet Rack
Upright: 3" x 1-5/8" x 10' Tall, 14 gauge

Shop Husky 48x120 IU18 Add-On Sections →
Husky 48" x 144" Add-On Pallet Rack Upright: 3" x 1-5/8", 14 gauge. 12' Tall
Husky 48" x 144" Add-On Pallet Rack
Upright: 3" x 1-5/8"x 12' Tall, 14 gauge

Shop Husky 48x144 IU18 Add-On Sections →
Husky 48" x 192" Add-On Pallet Rack Upright: 3" x 3", 14 gauge, 16' Tall
Husky 48" x 192" Add-On Pallet Rack
Upright: 3" x 3" x 16' Tall, 14 gauge

Shop Husky 48x192 IU24 Heavy Duty Add-On Sections →
 

Husky builds the 48 inch deep frame on two columns, and the frame code at the front of every model number tells you which one you are looking at. IU18 is the standard column, 3 inches by 1-5/8 inches in 14 gauge steel, rated 18,160 pounds at 48 inch beam spacing and offered in 96, 120 and 144 inch heights. IU24 is the heavy duty column, 3 inches by 3 inches in 14 gauge, rated 25,390 pounds at the same spacing and offered at 192 inches, the one height in the 48 inch line where three or four loaded levels make the heavier column necessary. The beams and their ratings are identical on both; the column decides how much total weight a frame carries. Frame depth does not change the frame rating, so a 48 inch IU18 frame carries the same 18,160 pounds as a 42 inch IU18 frame.

Two rules shape every installation. Height to depth is limited to 6 to 1 measured to the top loaded beam, and a 192 inch frame on a 48 inch base works out to 4 to 1, so every height on this page stands without row spacers by the ratio alone. ANSI MH16.1 also requires a permanent load plaque of at least 50 square inches showing the maximum load per level and per bay, updated whenever the rack is reconfigured. Both rules are explained in the CustomMHS pallet racking guide.


Product Lines:
The tiles below are grouped as starters first, then add-ons, each in order of height. Starters begin a row and ship with two frames; add-ons extend a row and ship with one frame, sharing the frame already standing at the end of the row, so a row of N bays is one starter plus N minus 1 add-ons, all on the same frame code. Heights of 96, 120 and 144 inches carry two or three beam levels and 192 inches carries three or four. Every section is offered in 48, 96, 108, 120 and 144 inch bay widths with or without 48 inch deep wire decking.

Selecting the Right Model:
◆ Pick 48 inch depth when the load is 48 inches deep or deeper, when nothing may overhang the beams, or when drums, crates and long cartons need support across the full depth. A standard 48 by 40 inch GMA pallet loaded 48 inches deep is normally run on a 42 inch frame with a 3 inch overhang each side; it sits flush on a 48 inch frame, which some operations prefer for neat aisles and rear flue control.
◆ Pick the frame code from the bay total. IU18 (3 by 1-5/8 inch, 14 gauge, 18,160 pounds at 48 inch spacing) covers two and three level rows up to 144 inches. The 192 inch height comes only on IU24 (3 by 3 inch, 14 gauge, 25,390 pounds) because three or four loaded levels usually exceed the IU18 rating.
◆ Pick the height from load height times the number of levels plus about 6 inches of lift clearance per level. Confirm forklift lift height and sprinkler clearance before buying above 144 inches.
◆ Start with the heaviest pallet you will store, double it for a two-pallet bay or triple it for a three-pallet bay, and pick a beam pair rated above that total from the 3,000 to 8,873 pound range. Then add up every loaded level on a frame, counting both bays on a shared frame, and keep the total under the frame rating.
◆ Count bays, not frames. Buy one starter per row and one add-on for every additional bay, all on the same frame code, depth and height. A 48 inch deep add-on will not join a 42 inch deep row.
◆ Add wire decking when cartons, drums or loose items will sit on the beams or when your fire code or insurer asks for open decking under sprinklers. Decking on this line is 48 inches deep to match the frame; it does not raise the beam rating and is rated for distributed loads, not point loads.


When should I buy 48 inch deep pallet rack instead of 42 inch?

Buy 48 inch deep Husky frames when your pallets or loads are 48 inches deep or deeper and must be supported edge to edge, when nothing may overhang the beams into the aisle or the flue, or when you store drums, crates and long cartons that need the full depth under them; buy 42 inch deep frames for standard 48 by 40 inch GMA pallets, which are designed to overhang the beams 3 inches front and back and are the most common load in a warehouse. The frames carry the same ratings at either depth (18,160 pounds for IU18 and 25,390 pounds for IU24 at 48 inch beam spacing) and take the same beams rated 3,000 to 8,873 pounds per pair, so depth changes what fits and how it sits, not what the rack holds. A 48 inch row uses 6 more inches of floor per row than a 42 inch row. The CustomMHS pallet racking guide explains why every capacity has a condition attached (guide section 1), how frames, beams and bays make up a row (section 2), how frame depth and height are matched to the load (section 6), anchoring and load plaques (section 7and section 8), and wire decking ratings (section 10).


Where Commonly Used:
Husky 48 inch deep pallet racking is used in warehouses, distribution centers and manufacturing plants to store deep or oversized pallet loads such as furniture, HVAC equipment, appliances, crated machinery, drums and building materials two to four levels high on forklift and reach truck aisles.

CustomMHS carries the full line of Husky Invincible pallet rack, backed by the manufacturer’s warranty.

Frequently Asked Questions (FAQs)

How does 48 inch compare with the 36 and 42 inch depths?

Depth is what separates them, and the tier availability differs as a result. The 42 inch page offers Heavy, Extra Heavy, and Extreme Duty across five heights up to 20 feet. This 48 inch depth offers four configurations up to 16 feet. Choose 48 inch when load depth requires it, then confirm the height you need exists at this depth before planning the layout.

What is the difference between a starter and an add-on unit?

A starter includes two uprights and shelf levels, and it begins each row or works as a standalone bay. An add-on includes one upright and shelf levels, sharing a common upright with the adjacent bay. Both come with or without wire decking, and each of the four configurations is available in both forms.

How many add-on units do I need?

Count bays rather than uprights. A row of four bays needs one starter and three add-ons, since each add-on shares an upright with the bay before it. Ordering a starter for every bay adds uprights the row does not need and consumes extra floor space.

What should I confirm before ordering?

Measure your load footprint against the 48 inch depth, since overhanging product is what determines the depth required rather than the pallet size alone. Check ceiling clearance including sprinklers and lighting, then subtract the working clearance your forklift mast needs. And weigh your heaviest pallet against the configuration you are considering, remembering that only the 16 foot option uses the larger upright.