Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

Cantilever Racking vs. Pallet Racking: Which Is Right for Long or Bulky Loads?

Pallet racking stores loads that fit between two uprights. Cantilever racking stores loads that do not. Here is how to tell which one your material needs.

Written and reviewed by: Tom McGovernPublished: November 2026Covers: MECO cantilever · MECO and Husky pallet rackingQuestions: 866-333-0728
Section One

Cantilever or pallet racking?

The deciding fact is whether the load fits between two uprights.

Short answer: Use pallet racking for palletized loads that fit inside a bay. Use cantilever racking for long, bulky or odd-length material such as lumber, pipe, bar stock and sheet goods, because it has no front column to load around.

Quick answers
  • Pallet racking: The load sits on two beams between front and rear uprights. The uprights limit the load length to the bay width.
  • Cantilever racking: The load sits on arms that stick out from a single column. The front is open for the full length of the run.
  • Go cantilever for: Material longer than the widest beam you can use, or material with no pallet under it.

The longest roll-formed step beam we list is 144 in. Anything over 12 ft cannot go into a pallet rack bay without sticking out past an upright. That is the practical line between the two systems.

A note on this guide

This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.

Section Two

How each rack carries the load

Two different structures with two different failure modes.

Short answer: A pallet rack beam is supported at both ends. A cantilever arm is supported at one end, so capacity falls quickly as the arm gets longer.

Pallet racking

Beams between uprights

Each beam is held at both ends. A pair of beams shares the load equally. Longer beams hold less, but the effect is gradual. Most damage comes from lift truck impact.

Cantilever racking

Arms off a column

Each arm is held at one end, so the load is always trying to bend the arm down and tip the column forward. The base and the anchors resist that constantly, loaded or not.

MECO Series 1000 arm capacity by length
Arm lengthCapacity per arm
12 in.1,000 lb
18 in.750 lb
24 in.600 lb
30 in.500 lb
36 in.400 lb
42 in.350 lb
48 in.300 lb

Going from a 12 in. arm to a 48 in. arm is four times the reach and about 70 percent less capacity. Size the arm to the load depth and no longer.

Section Three

Side by side

The practical differences on the floor.

Short answer: Cantilever wins on long material and loading speed. Pallet racking wins on palletized density and cost per position.

Cantilever vs. pallet racking
Cantilever rackingPallet racking
Best loadLumber, pipe, tube, conduit, bar stock, structural steel, sheet goodsPalletized and unitized loads
Load lengthLimited by the run, not the bayLimited by the beam, up to 144 in. on listed step beams
Front accessOpen, no front columnUprights at each bay
AdjustmentArms on 3 in. centersBeams in 2 in. increments
Capacity statedPer arm, per upright and per systemPer beam pair and per upright frame
Governing standardANSI MH16.3ANSI MH16.1
Floor spaceBase length set by arm length, 33 to 62 in. single sidedFrame depths of 36, 42 and 48 in.

The two standards are separate. ANSI MH16.1 covers pallet rack and excludes cantilever. ANSI MH16.3 covers cantilever. A rack built to one is not automatically compliant with the other.

Section Four

Choosing by load

Find the row that matches your material.

Short answer: Round, long or unpalletized material goes on cantilever. Anything on a pallet that fits a bay goes in pallet rack.

Lumber, timber, sheet and panel goods
Cantilever with straight arms.
Pipe, round tube, conduit, round bar
Cantilever with inclined arms so material cannot roll off. Straight and inclined arms carry the same rated capacity at every length.
Bar stock and structural steel in mixed lengths
Cantilever. Short offcuts concentrate load on one or two arms, so keep them on lower levels and against the column.
Standard pallets, cartons, drums on pallets
Pallet racking. See the pallet racking guide.
Long loads that are palletized or crated
Depends on length. Up to the beam length, pallet racking with the right beam. Beyond it, cantilever.
Storage against a wall
Single-sided cantilever or a single row of pallet rack. A wall does not stop a cantilever from tipping forward, so base length and anchors still matter.
Storage in open floor with aisles both sides
Double-sided cantilever nearly doubles the arm count for well under double the cost, because the column, base and bracing are shared.
Section Five

Worked example: a bundle of bar stock

Check the arm, then the series.

Short answer: Divide the bundle weight by the number of arms under it, then compare with the arm rating at your arm length.

A 2,400 lb bundle, 24 in. deep, sits across four arms. That is 2,400 / 4 = 600 lb per arm. A MECO Series 1000 arm at 24 in. is rated 600 lb. The arm is at its limit with no margin.

Step up to Series 4000, where a 24 in. arm is rated 2,000 lb, and the same bundle uses 30 percent of the arm rating. Published starter units show the difference: the Series 1000 SM8 and the Series 4000 SU8 are both 8 ft tall with eight 24 in. arms, at 600 lb and 2,000 lb per arm.

Published MECO starter units
ModelSeriesHeight x baseArmsPer arm
SM810008 ft x 33 in.8 x 24 in.600 lb
SU840008 ft x 37 in.8 x 24 in.2,000 lb
SU10400010 ft x 49 in.12 x 36 in.1,200 lb
SU12400012 ft x 61 in.16 x 48 in.1,000 lb
Three capacities, not one

Check the arm, then the upright, then the whole system. A load can pass on the arm and still overload the column once every level is full.

Section Six

Common mistakes

What goes wrong when the wrong rack is chosen.

Short answer: The most common error is forcing long material into pallet rack, followed by buying arms longer than the load.

  • Long stock across pallet rack beams. Material hanging past the uprights gets hit, and the beams were rated for an evenly spread load.
  • Oversized arms. Longer arms cost more and hold less. Match arm length to load depth.
  • Mixing series. MECO Series 1000, 2000 and 4000 uprights, arms and brace sets are not interchangeable.
  • Leaving out braces. Brace sets are structural and series-specific. They are not optional.
  • Loading heavy at the top and at the arm tip. Heavy material belongs on the lower arms and against the column.

For arm types, bases and starter and add-on units, see our cantilever racking guide.

Section Seven

Frequently asked questions

The questions I hear most on quote calls.

What is the difference between cantilever racking and pallet racking?

Pallet racking supports loads on beams between front and rear uprights. Cantilever racking supports loads on arms that extend from a single column, leaving the front open for long material.

When should I use cantilever racking?

Use it for long, bulky or unpalletized material such as lumber, pipe, tube, conduit, bar stock, structural steel and sheet goods.

Can I store long material in pallet racking?

Only if it fits inside the bay. The longest roll-formed step beam we list is 144 in., so material over 12 ft will extend past the uprights.

How much weight can a cantilever arm hold?

It depends on the series and arm length. A MECO Series 1000 arm is rated 1,000 lb at 12 in. and 300 lb at 48 in. A Series 4000 arm is rated 2,000 lb at 24 in.

Do cantilever and pallet racks follow the same standard?

No. Pallet racking is covered by ANSI MH16.1 and cantilever racking is covered by ANSI MH16.3.

Is double-sided cantilever worth it?

In open floor space, yes. It nearly doubles the arm count for well under double the cost. It needs a working aisle on both faces.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting MECO cantilever racking and MECO and Husky pallet racking.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Long loads and not sure which rack?

Send us the material, its length, the bundle weight and how you load it, and we will lay out the rack. Quote requests are answered within 24 hours by a real person.

866-333-0728

Browse cantilever racking at custommhs.com

Browse pallet racking

Get a fast quote

No bots. No guesswork. Real experts.

Specification sources

CustomMHS cantilever racking and pallet racking guides · MECO-Omaha Series 1000, 2000 and 4000 product data · ANSI MH16.3 (cantilever) and ANSI MH16.1 (pallet rack).

Published figures are current as of November 2026 and are subject to change by the manufacturer. This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.