Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

How to Size a Lift Table: Capacity, Platform Size and Travel

Three numbers size a lift table: how much it lifts, how big the platform is and how far it travels. Each one has a catch. Here is how to get all three right.

Written and reviewed by: Tom McGovernPublished: November 2026Covers: Autoquip · Presto · Bishamon · Lift Products · Blue GiantQuestions: 866-333-0728
Section One

How do you size a lift table?

Size it in this order: capacity, platform, lowered height, travel, duty.

Short answer: Pick a capacity above your heaviest load including how it arrives, a platform that fits the load without much extra, a lowered height your loading method can reach, and enough travel to hit your top working height.

Quick answers
  • Capacity: Heaviest load, plus a rolling load allowance if it rolls on.
  • Platform: As large as the load, and no larger than needed. Oversize platforms lose edge load rating.
  • Lowered height: Decides whether a pallet jack can load it.
  • Travel: Working height equals lowered height plus travel.
  • Duty: Count cycles at the busiest hour.

The lines we carry run from 250 to 24,000 lb and from 3/8 to 94 in. of travel. With that much range the right table exists. The work is in asking the right questions before you order.

A note on this guide

This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.

Section Two

Capacity

The rated capacity assumes a load set down in the middle.

Short answer: Start with the heaviest load. If it rolls on, multiply the axle load by 1.5.

Set-down loads

If a fork truck or hoist sets the load on the platform, the capacity you need is the weight of the heaviest load plus anything that rides with it: the pallet, a fixture, a conveyor section.

Rolling loads

A load that rolls onto the platform puts its weight on one edge first, with impact. The published rule is axle load times 1.5. A 2,000 lb two-axle cart puts 1,000 lb on each axle. Times 1.5 that is 1,500 lb per axle at the edge, which is equivalent to a 3,000 lb static load. A loaded fork truck carries 80 to 90 percent of its weight on the front axle, which is why driving a fork truck onto a lift table takes a much larger table than the load suggests.

Direction and placement

Most scissor designs are much stronger over the ends than the sides. The load's center of gravity has to stay inside the outline of the legs, including while it is being transferred on or off.

Section Three

Platform size

Bigger is not safer.

Short answer: Edge load capacity drops 2 percent for every inch the platform is oversized, in each direction.

Every table has a minimum platform size that matches its base. A platform can be made larger, but the overhang gives edge loads more leverage. The published derating is 2 percent per inch beyond the minimum width and 2 percent per inch beyond the minimum length.

Example: a platform 24 in. wider than the minimum loses 24 x 2 = 48 percent of its edge load rating on that side.

If you need a big platform for a big load, buy a wide base model instead of oversizing a standard one. The wide base widens the leg stance under the load.

Wide base and oversized platform families
BrandFamilyPublished detail
PrestoX3W, X4W, X4.5WBase 3 to 4-1/2 ft wide; platforms to 84 x 120 in.
Lift ProductsLPT3W, LPT4W3 and 4 ft bases; platforms to 72 x 108 in.
AutoquipSeries 35 Extra Wide2,500 to 15,000 lb
AutoquipSeries 35 Double LongTwo scissor sets end to end; 4,000 to 24,000 lb
Blue GiantStandard dutyPlatforms up to 48 x 120 in.
Section Four

Lowered height and travel

Travel is quoted as a range. The first number matters as much as the second.

Short answer: Working height equals lowered height plus travel. The lowered height decides how the table is loaded.

Lowered height by format
FormatLowered heightLoading
Floor level3/8 to 3-1/8 in.Pallet jack straight on
Low profile2.9 to 5 in.Pallet jack over a short ramp
Standard5 to 12-1/2 in.Fork truck, hoist or by hand

A table that collapses to 7 in. cannot be loaded by pallet jack. If there is no fork truck at the station, start with floor level or low profile and work up from there.

Worked example

You need a top working height of 36 in. and pallets arrive by pallet jack. A floor level table lowers to 3/8 in., so you need at least 36 - 3/8 = 35-5/8 in. of travel. The Blue Giant Zero Ground Level line is published from 3/8 to 36-1/2 in., which covers it.

With a fork truck available, a standard table works. The Presto XL36-50 goes from 7-1/4 to 43 in. on 36 in. of travel at 5,000 lb.

Representative published models
ModelBrandCapacityLowered to raisedPlatform
S35-024-0025Autoquip2,500 lb6.5 to 30.5 in.24 x 36 in.
XL24-20Presto2,000 lb7-1/4 to 31 in.24 x 36 in.
LPT-045-36Lift Products4,500 lb7.25 to 43 in.24 x 48 in.
L22K-3153Bishamon2,200 lb8.5 to 38.5 in.31 x 53 in.
S35-060-0150Autoquip15,000 lb12.5 to 72.5 in.32 x 90 in.
Section Five

Duty and power

How often it cycles decides how long it lasts.

Short answer: Count cycles at the busiest hour. Under about 10 per hour is comfortable. At 15 or more, discuss duty before you order.

Duty as published
BrandFigure
Autoquip100,000 cycles per year, intermittent
Bishamon50,000 cycles per year (L22K, L44K); 35,000 (L66K)
Lift ProductsUp to 15 minutes of run time per hour
Presto15 cycles per hour cited as the overheating threshold
Blue GiantNot published

Voltage is part of the model. Bishamon lists 115 VAC, 230 V single phase, 230 V three phase and 480 V three phase as separate part numbers. Presto and Blue Giant list 115 V single phase on standard models. Tell us what power is at the station.

Safety items to specify

Toe guards or accordion skirting close the pinch points under the platform. Add guard rails and gates where people ride or work on it. ANSI MH29.1-2020 is the governing standard for industrial scissors lifts.

Section Six

Common mistakes

Five ways a correctly rated table ends up wrong.

Short answer: The usual errors are sizing to the static weight of a rolling load, oversizing the platform, and missing the lowered height.

  • Ignoring rolling loads. Multiply the axle load by 1.5.
  • Ordering a bigger platform to be safe. Each extra inch costs 2 percent of edge load rating.
  • Not checking the lowered height. Above about 5 in., a pallet jack cannot load it.
  • Confusing travel with raised height. Working height is lowered height plus travel, not travel alone.
  • Loading from the side without checking. Scissor tables are stronger over the ends.

For self-leveling units see scissor lift table vs. pallet positioner. For brand detail see our lift tables by brand guide.

Section Seven

Frequently asked questions

The questions I hear most on quote calls.

How do I choose lift table capacity?

Use the weight of the heaviest load plus anything that rides with it. If the load rolls on, multiply the axle load by 1.5 to allow for impact.

How big should the lift table platform be?

As large as the load and no larger than necessary. Edge load capacity drops 2 percent for every inch beyond the minimum platform width or length.

What is lift table travel?

Travel is the distance the platform moves. Raised working height equals lowered height plus travel.

Can I load a lift table with a pallet jack?

Yes, with a floor level table that lowers to 3/8 to 3-1/8 in., or a low profile table with a short ramp. A table that collapses to 7 in. cannot be loaded by pallet jack.

How many cycles per hour can a lift table run?

It depends on the brand. Under about 10 cycles per hour is comfortable. Presto cites 15 cycles per hour as the overheating threshold, and Lift Products rates for up to 15 minutes of run time per hour.

What standard covers scissor lift tables?

ANSI MH29.1-2020, Safety Requirements for Industrial Scissors Lifts.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting scissor lift tables, low profile lift tables and pallet positioners.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Want us to size it?

Send us the load weight and size, how it gets on the table, and the lowest and highest working height, and we will match a model. Quote requests are answered within 24 hours by a real person.

866-333-0728

Browse lift tables at custommhs.com

Browse scissor lift tables

Browse low profile lift tables

Get a fast quote

No bots. No guesswork. Real experts.

Specification sources

CustomMHS lift tables guide, lift tables by brand guide and product listings · Advance Lifts published white paper on rolling and edge loads · ANSI MH29.1-2020.

Published figures are current as of November 2026 and are subject to change by the manufacturer. This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.