Section OneHow do you size a modular drawer cabinet?
Work from the smallest thing to the largest: part, drawer, cabinet, aisle.
Short answer: Pick the width from your longest flat item, the drawer heights from your tallest items, the housing height from the drawer stack, and then check the aisle with a drawer fully open.
Quick answers- Width: Longest flat item plus 2 in., then the next standard width.
- Drawer height: Tallest item in that drawer plus about 1 in.
- Usable drawer stack: Housing height minus about 4 in.
- Aisle: Cabinet depth plus drawer projection plus 30 in. of working space.
- Capacity: 400 lb per drawer on the R-Series, with full extension.
The figures in this guide are the published Rousseau R-Series numbers, because that is the line most of our customers build. The method works for any modular drawer cabinet.
A note on this guideThis guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.
Section TwoWidth and depth
The footprint is set by your longest part and your floor space.
Short answer: R-Series widths are 24, 30, 36, 48, 54 and 60 in. Depths are 18, 21, 24 and 27 in., depending on the width.
R-Series widths and the depths offered| Width | Depths | Model prefix |
|---|
| 24 in. | 21 in., 27 in. | R5ACD, R5ACG |
| 30 in. | 21 in., 27 in. | R5ADD, R5ADG |
| 36 in. | 18 in., 24 in. | R5AEC, R5AEE |
| 48 in. | 24 in., 27 in. | R5AHE, R5AHG |
| 54 in. | 24 in., 27 in. | R5AJE, R5AJG |
| 60 in. | 24 in., 27 in. | R5AKE, R5AKG |
Width rule. Measure the longest flat item, add 2 in., and buy the next standard width. A 41 in. part needs 43 in., so it goes in a 48 in. cabinet. In a 36 in. drawer it would have to sit diagonally.
Depth. Deeper drawers hold more but need more aisle. Choose depth after you have checked the aisle in section five.
Section ThreeDrawer heights and the drawer mix
This is where most of the storage is won or lost.
Short answer: Size each drawer to its tallest item plus about 1 in. Drawer heights run from 3 to 14 in.
Drawer height by contents| Contents | Drawer height |
|---|
| Inserts and taps | 3 in. |
| Hand tools | 4 to 6 in. |
| Collets | 5 to 8 in. |
| Die sets | 8 to 12 in. |
| Power tools and PPE | 10 to 14 in. |
A drawer that is too tall wastes the air above the parts. A 60 in. cabinet full of 6 in. drawers holds nine drawers. The same shell with a mix of 3, 4 and 6 in. drawers holds fifteen.
Four published drawer mixes in the same 48 x 24 x 60 in. shell| Model | Drawers | Count | Suits |
|---|
| R5AHE-5805 | (10) 3 in., (3) 4 in., (2) 6 in. | 15 | Many small part numbers |
| R5AHE-5813 | (9) 6 in. | 9 | Uniform mid-size items |
| R5AHE-5807 | (3) 6 in., (3) 12 in. | 6 | Bulky tooling, fixtures, power tools |
| R5AHE-5822 | (6) 4 in., (1) 8 in., (1) 10 in., (1) 12 in. | 9 | Mixed maintenance stock |
Section FourCabinet height and capacity
The drawer stack has to fit the housing, and the load has to fit the drawers.
Short answer: Usable drawer height is about the housing height minus 4 in. Every R-Series drawer is rated 400 lb.
Height
Housing heights are 24, 28, 30, 34, 38, 44 and 58 in. The standard 2 in. forklift base adds 2 in., so a 58 in. housing stands 60 in. overall. An optional 4 in. base adds 2 in. more. A 58 in. housing gives about 54 in. of drawer stack.
Check it against a published unit: the R5AHE-5805 has ten 3 in., three 4 in. and two 6 in. drawers. That is 30 + 12 + 12 = 54 in. It fills the housing exactly.
Overall heights of 30 to 40 in. work as bench height. Cabinets 46 and 60 in. tall are storage first.
Capacity
Each drawer is rated 400 lb with full extension and 100 percent access, and the rolling mechanism carries a lifetime warranty. The published R5AEE-5818 (36 x 24 x 60 in., 14 drawers) is rated 5,600 lb total, which is 14 x 400, and weighs 670 lb empty. Add those together when you check the floor.
Anchor tall cabinetsAnchor anything 46 in. or taller, anything with heavy tooling in the upper drawers, and anything in a seismic zone. Specify one-drawer-at-a-time (RB15) on 60 in. units with heavy tooling.
Section FiveLayout: aisle space with a drawer open
A drawer cabinet needs room in front of it that a shelf does not.
Short answer: Aisle needed equals cabinet depth plus drawer projection plus 30 in. of working space.
For a 27 in. deep cabinet the drawer projects about 25 in. The math is 27 + 25 + 30 = 82 in., or about 7 ft from the wall behind the cabinet to the far side of the working space.
Aisle check| Aisle in front of the cabinet | Result with a drawer fully open |
|---|
| 6 ft | A little over 3 ft of passage remains |
| 4 ft | The aisle is blocked |
Inside the drawer, partitions and dividers adjust in 1 in. increments. Leave one empty lane at the back of each drawer for part numbers you do not have yet.
Section SixCommon mistakes
All of these are fixed on paper before the order.
Short answer: The usual errors are buying one drawer height throughout, sizing width to the average part, and forgetting the open-drawer aisle.
- All drawers the same height. Mixed heights can nearly double the drawer count in the same shell.
- Width sized to the average part. Size to the longest item plus 2 in.
- Ignoring the aisle. Measure with a drawer fully out.
- Adding up drawer ratings without checking the floor. 400 lb is the drawer limit. The floor still has to carry the whole cabinet.
- Choosing the shell before the mix. Two cabinets with the same outside dimensions can differ by well over a thousand dollars depending on the drawer mix. Decide the mix first.
For model numbers, accessories and locks, see our Rousseau R-Series guide. To build your own, use the Rousseau configurator.
Section SevenFrequently asked questions
The questions I hear most on quote calls.
How do I choose the width of a modular drawer cabinet?
Measure your longest flat item, add 2 in., and buy the next standard width. Rousseau R-Series widths are 24, 30, 36, 48, 54 and 60 in.
What drawer heights are available?
Rousseau R-Series drawers run from 3 to 14 in. high. Common heights are 3, 4, 5, 6, 7, 8, 9, 10, 12 and 14 in.
How much weight can a modular cabinet drawer hold?
Every Rousseau R-Series drawer is rated 400 lb with full extension. Light-duty series are rated 100 lb per drawer.
How many drawers fit in a 60 in. tall cabinet?
It depends on the mix. A 58 in. housing has about 54 in. of drawer stack. Published 48 x 24 x 60 in. units range from 6 drawers to 15 drawers.
How much aisle space does a drawer cabinet need?
Cabinet depth plus drawer projection plus 30 in. of working space. For a 27 in. deep cabinet that is about 82 in., or roughly 7 ft.
Do modular drawer cabinets need to be anchored?
Anchor cabinets 46 in. or taller, cabinets with heavy tooling in upper drawers, and cabinets in seismic zones.