Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

Nestable, Stackable or Rackable Plastic Pallets: Which Type Do You Need?

Three pallet types that look alike on a listing and behave very differently under load. Here is how to match the pallet to where it will sit.

Written and reviewed by: Tom McGovernPublished: November 2026Covers: Nestable · Stackable · Rackable plastic palletsQuestions: 866-333-0728
Section One

Which plastic pallet type do you need?

The answer comes from one question: what is underneath the pallet when it is loaded?

Short answer: Use a nestable pallet for shipping and floor storage where empties come back, a stackable pallet when loaded pallets sit on top of each other, and a rackable pallet any time the load spans open rack beams.

Quick answers
  • Nestable: Lightest and lowest cost per trip out. Nests when empty. Floor and shipping use.
  • Stackable: Bottom runners spread the load so loaded pallets stack. Needs full support under it.
  • Rackable: Reinforced to span two beams with nothing in between. Heaviest and usually the most expensive.

Plastic pallets are sold by type because the bottom of the pallet is built differently on each one. A nine-leg nestable has no bottom deck at all. A stackable adds runners. A rackable adds a continuous runner base and, on many models, steel reinforcement. The top deck can look identical on all three.

A note on this guide

This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.

Section Two

How each type is built

The underside tells you what the pallet is for.

Short answer: Legs mean nestable, runners mean stackable, and a reinforced three-runner or perimeter base means rackable.

Nestable

Open underside, commonly nine legs

Legs drop into the pallet below when empty. Typically 20 to 30 lb. Suppliers claim up to four times the space efficiency when shipping empties.

Stackable

Runners added under the legs

Often the same mold as a nestable with runners added. The runners spread the weight across the load below. It needs full support underneath.

Rackable

Continuous three-runner or perimeter base

Built for open-beam, push-back and edge racks. Commonly 35 to 55 lb. Steel reinforcement is common because steel is about 30 times stiffer than polypropylene or HDPE.

Plastic pallet types compared
TypeTypical weightNests emptyStacks loadedOpen rack beams
Nestable20 to 30 lbYesNoNo
StackableVaries by runner designNoYesOnly on a wire mesh deck
Rackable35 to 55 lbNoYesYes
Section Three

Load ratings by type

The same pallet carries three different ratings, and the type decides how far apart they are.

Short answer: Nestable pallets show the widest gap between static and dynamic ratings. Only a rackable pallet carries a racking rating you can use.

Every plastic pallet has a static rating (sitting on a flat floor), a dynamic rating (being moved by a forklift or pallet jack) and a racking rating (supported at two edges with nothing beneath). The racking number is normally the lowest and is often left off spec sheets for pallets that were never meant for a rack.

Published examples of the gap between ratings
PalletStaticDynamicRatio
Nestable, example one10,500 lb1,500 lbAbout 7 to 1
Nestable, example two20,000 lb5,000 lb4 to 1
Galvanized wire pallet, 40 x 48 in.4,000 lb2,500 lbAbout 1.6 to 1

A stackable pallet rated 30,000 lb on the floor may still be unsuitable across beams. A floor rating tells you nothing about what the pallet does when the middle is unsupported. Our guide on pallets goes through the three ratings one at a time.

Ask for all three in writing

When you request a quote, ask for the static, dynamic and racking rating of the exact model. If the racking rating is missing, treat the pallet as not rackable.

Section Four

Choosing by application

Find the row that matches how the pallet is used.

Short answer: Decide by the most demanding thing the pallet will ever do. A pallet that goes in a rack even once needs to be rackable.

One-way or closed-loop shipping with empties returning
Nestable. The space saved on the empty leg is the whole reason this type exists.
Floor storage, loaded pallets not stacked
Nestable is usually enough. Check the dynamic rating against your load.
Loaded pallets stacked on each other
Stackable. The runners keep the legs from punching into the load below.
Selective rack with wire mesh decking
Stackable can work because the deck supports the runners. Confirm with the pallet maker and check the deck rating.
Open-beam, push-back or edge rack
Rackable only. Ask for the racking rating at your beam spacing.
Cold storage or freezer
Check the material. HDPE has a published service range of about -40 to 140°F. Polypropylene turns brittle below freezing.
Steam, autoclave or hot washdown
Polypropylene, with a published service range of about 50 to 230°F.

Browse the three types here: nestable plastic pallets, stackable plastic pallets and rackable plastic pallets.

Section Five

Worked example: what nesting saves on the return trip

The formula is simple and worth running before you choose.

Short answer: Return trips saved equals empties per trailer nested, divided by empties per trailer stacked, minus one.

Say a trailer returns a set number of empty stackable pallets, and the nestable version of the same footprint fits four times as many. The math is 4 divided by 1, minus 1, which is 3. One trailer brings back what used to take four, so three return trips are saved for every four you ran before.

Run the numbers with the stack heights your carrier allows and the nested height on the spec sheet for your model. The four to one figure is a supplier claim for best cases, so use your own count.

Where the saving disappears

If loaded pallets must stack in your warehouse, or the pallet goes in a rack, a nestable is the wrong pallet no matter what it saves on freight.

Section Six

Common mistakes

Each one is cheap to avoid before the order.

Short answer: Most pallet failures come from using a floor pallet in a rack or reading the static rating as the working rating.

  • Buying on the static rating. The static number is the largest and is often printed largest. It only applies on a flat floor.
  • Putting a stackable pallet on open beams. Without wire decking or a pallet support, a stackable pallet spans the beams on runners that were not designed for it.
  • Ignoring creep and temperature. Plastic deflects slowly under a sustained load. Rack ratings are typically set at about 70°F, and heat lowers them.
  • Forgetting fire classification. Under NFPA 13, plastic pallets raise the commodity class of what is stored on them. Tell whoever handles your fire protection that you are changing from wood.
  • Mixing types in one fleet. A nestable and a rackable pallet should not be interchangeable on your floor. Color-code them or keep them in separate areas.
Section Seven

Frequently asked questions

The questions I hear most on quote calls.

What is the difference between nestable, stackable and rackable pallets?

A nestable pallet has legs that drop into the pallet below when empty. A stackable pallet adds bottom runners so loaded pallets can sit on each other. A rackable pallet has a reinforced base that can span open rack beams.

Can I put a nestable pallet in a pallet rack?

Not on open beams. A nestable pallet has no bottom structure to span the gap between the beams. Use a rackable pallet.

Can a stackable pallet go in a rack?

Only when it is fully supported, for example on wire mesh decking, and only if the pallet maker and the deck rating allow it. On open beams, use a rackable pallet.

Which plastic pallet type costs the least?

Nestable pallets are the lightest, typically 20 to 30 lb, and are usually the lowest cost. Rackable pallets, commonly 35 to 55 lb, are usually the most expensive.

How much do plastic pallets weigh?

Nestable pallets typically weigh 20 to 30 lb and rackable pallets commonly weigh 35 to 55 lb. Heavy-duty plastic pallets run up to 55 lb.

Are plastic pallets exempt from ISPM-15?

Yes. Plastic pallets are exempt from the ISPM-15 heat treatment rule that applies to wood packaging for export.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting nestable plastic pallets, stackable plastic pallets and rackable plastic pallets.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Not sure which pallet type fits?

Tell us the load weight, how the pallet is handled and whether it goes in a rack, and we will match it. Quote requests are answered within 24 hours by a real person.

866-333-0728

Browse plastic pallets at custommhs.com

Get a fast quote

No bots. No guesswork. Real experts.

Specification sources

CustomMHS pallets buyer's guide and product listings · ISO 8611 (pallet test methods and working loads) · NFPA 13 and FM Global Data Sheet 8-24 (plastic pallet commodity classification).

Published figures are current as of November 2026 and are subject to change by the manufacturer. This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.