Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

What Is an ESD Container? When Static-Safe Totes and Bins Are Required

An ESD container is molded from a material that bleeds off static charge in a controlled way. Here is how it works, how to read the rating, and when you need one.

Written and reviewed by: Tom McGovernPublished: November 2026Covers: LEWISBins · Akro-Mils · MFG · RousseauQuestions: 866-333-0728
Section One

What is an ESD container?

ESD stands for electrostatic discharge.

Short answer: An ESD container is a tote, bin or divider box made from a conductive or static dissipative plastic, so static charge drains away slowly instead of building up and jumping to the parts inside.

Quick answers
  • The problem: Ordinary plastic is an insulator. It builds and holds a charge.
  • The fix: A material that bleeds charge away in a controlled manner rather than dumping it.
  • When required: Whenever unprotected static-sensitive electronic parts or assemblies are handled, stored or moved.
  • The catch: Black is a convention, not a specification. Ask for the measured resistance.

Moving a bag of circuit boards in and out of a standard polypropylene bin can generate enough discharge to damage components. The damage often does not show until the product is in the field, which is what makes it expensive.

A note on this guide

This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.

Section Two

Insulative, dissipative, conductive

Static-safe materials are sorted by electrical resistance.

Short answer: Too high and the charge stays put. Too low and it discharges all at once. The useful range is in between.

Surface resistance ranges cited in our container guides
RangeBehaviorWhat it means
Above 1012 ohmsInsulativeOrdinary plastic. Builds and holds a charge.
106 to 109 ohmsTarget dissipative rangeCharge bleeds away slowly and safely.
Below 105 ohmsVery conductiveToo conductive to protect against charged-device and charged-board events.

Akro-Mils publishes its ESD bins in the static dissipative range of 104 to 1011 ohms per square, and notes the low carbon content, which keeps the bin from leaving black residue on parts.

Why slower is better: in published test data, dissipative material limited discharge current to about 0.6 to 5.1 mA, while overly conductive material produced 100 to 132 mA with visible sparking. Makers of sensitive devices target a 10 mA peak limit.

Black does not mean ESD safe

In that same data, over half of the black ESD materials measured fell below 105 ohms. Color tells you nothing. Request the measured surface resistance for the exact product.

Section Three

When are ESD containers required?

The requirement comes from your parts and your ESD program.

Short answer: You need them when unprotected static-sensitive items go inside. You do not need them for parts that are not sensitive or that stay sealed in shielding packaging.

ANSI/ESD S20.20 is the standard for ESD control programs cited in our container guide. If your company or your customer works to it, the containers used inside the protected area are part of that program, and the program sets the resistance range.

Bare circuit boards and populated assemblies
ESD containers. This is the core use.
Loose components: chips, connectors with electronics, sensors
ESD bins or divider boxes.
Board repair and rework benches
ESD bins at the bench and ESD totes between stations.
Customer or contract calls out ANSI/ESD S20.20
ESD containers that meet the range in the program, with documentation.
Mechanical parts, fasteners, non-electronic stock
Standard containers. ESD material adds cost and no benefit.
Electronics plus heat
MFG Fibrestat composite, the ESD formulation in the fiberglass line.
Section Four

ESD container types we carry

The same container styles, in static-safe material.

Short answer: Divider boxes for kitting, hopper bins for the bench, drawer bins for cabinets, and fiberglass where heat is also a factor.

Static-safe containers at CustomMHS
ProductPublished detailUse
LEWISBins ESD divider boxesBlack XL conductive, stack only, 40 lb, 1.25 in. divider centers, 10.8 x 8.3 in. to 22.4 x 17.4 in., 2.5 to 12 in. highKitting and separating components
Akro-Mils ESD bin 3024014.75 x 8.125 x 7 in., 60 lb, black, 104 to 1011 ohms per squareHopper-front bins at the bench or on panels
Rousseau RG21 conductive binDrawer bin for R-Series cabinetsComponents stored in modular drawers
MFG FibrestatESD formulation of glass-reinforced compositeStatic-sensitive work where heat is present

See them here: ESD containers and divider boxes and ESD small parts bins.

Section Five

How to specify and maintain

An ESD container only works as part of a grounded system.

Short answer: Specify the resistance range, get it in writing, and keep the containers clean and on a grounded surface.

  1. Ask what resistance range your ESD program requires.
  2. Request the measured surface resistance for the exact model and lot.
  3. Choose the style by use: divider box, hopper bin, tote or drawer bin.
  4. Set containers on a grounded bench, shelf or cart so the charge has somewhere to go.
  5. Keep labels and tape to a minimum. Ordinary labels and liners are insulators.
  6. Clean per the maker's instructions and re-test on the schedule your program sets.
Worked check

Your program calls for 106 to 109 ohms. A supplier quotes a black bin measured at 104 ohms. It is below the range, so it fails, even though it is sold as conductive.

Section Six

Common mistakes

Most of these come from treating ESD as a color.

Short answer: Buying black bins without a resistance figure is the most common and most costly error.

  • Buying by color. Ask for the number.
  • Insulating inserts. A standard divider or foam liner inside an ESD box defeats it.
  • Ignoring residue. Carbon-loaded plastics can shed. Low carbon content avoids black residue on parts.
  • No path to ground. A dissipative tote on an insulating shelf cannot drain.
  • Using ESD containers for everything. ESD material costs more. Use it where the parts need it.

For container styles and sizes, see our containers, totes and trays guide.

Section Seven

Frequently asked questions

The questions I hear most on quote calls.

What is an ESD container?

It is a tote, bin or box made from conductive or static dissipative plastic that drains static charge slowly, protecting static-sensitive electronic parts inside.

What does ESD stand for?

Electrostatic discharge, the sudden flow of static electricity between two objects.

When are ESD containers required?

When unprotected static-sensitive electronic parts or assemblies are handled, stored or moved, and whenever your ESD control program, such as one built on ANSI/ESD S20.20, calls for them.

Is a black bin an ESD bin?

Not necessarily. Black is a convention, not a specification. Ask for the measured surface resistance of the exact product.

What is the difference between conductive and static dissipative?

Both let charge move. Conductive material has lower resistance and moves it fast. Dissipative material has higher resistance and bleeds it off slowly, which limits the discharge current.

What resistance should an ESD container have?

Follow your ESD program. Our container guide cites a target surface resistance of 10 to the 6th to 10 to the 9th ohms, and Akro-Mils publishes its ESD bins at 10 to the 4th to 10 to the 11th ohms per square.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting ESD and conductive containers and divider boxes and ESD small parts bins.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Need static-safe containers specified?

Tell us what parts go in the container and what your ESD program calls for, and we will match the material and request the measured resistance. Quote requests are answered within 24 hours by a real person.

866-333-0728

Browse ESD containers, totes and trays at custommhs.com

Browse small parts bins

Get a fast quote

No bots. No guesswork. Real experts.

Specification sources

CustomMHS containers, totes and trays guide and small parts bins guide · ANSI/ESD S20.20 · LEWISBins and Akro-Mils published data.

Published figures are current as of November 2026 and are subject to change by the manufacturer. This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.