Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

How to Measure for Pallet Racking: Bay Width, Beam Height and Aisle Clearance in Feet and Inches

Five measurements decide whether a pallet rack order fits your loads, your building and your lift truck. Here is how to take each one.

Written and reviewed by: Tom McGovernPublished: November 2026Covers: Selective pallet rack · Beams · Uprights · AislesQuestions: 866-333-0728
Section One

What do you measure for pallet racking?

Start with the load, not the building.

Short answer: Measure the loaded pallet first (width, depth, height and weight), then the building (clear height, floor space, obstructions), then the lift truck (lift height and aisle requirement).

Quick answers
  • Beam length: Total load width plus clearance. Two 40 in. wide pallets fit a 96 in. beam.
  • Frame depth: Pallet depth minus 6 in. A 48 in. deep pallet goes on a 42 in. frame.
  • Beam level spacing: Load height plus lift-off clearance plus the beam itself, in 2 in. steps.
  • Run length: Beam length times bays, plus 3 in. for each upright.
  • Aisle width: Set by the lift truck. Get it from the truck's spec sheet.

Measure the load as it actually sits, including any product that overhangs the pallet. The rack is sized to the load, and the pallet is only part of it.

A note on this guide

This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.

Section Two

Beam length: how wide is the bay?

Beam length is the clear space between two uprights. It is measured inside to inside.

Short answer: Add the load widths, 5 in. of clearance at each upright and 6 in. between loads. Then pick the next standard beam length.

The commonly published rule is 5 in. between each upright and the load beside it, and 6 in. between loads. For two 40 in. wide pallets: 5 + 40 + 6 + 40 + 5 = 96 in. That is why 96 in. is the standard beam for two GMA pallets.

Beam length for common loads
Loads per levelLoad widthMathBeam to order
Two40 in.5 + 40 + 6 + 40 + 5 = 96 in.96 in. (8 ft)
Two48 in.5 + 48 + 6 + 48 + 5 = 112 in.120 in. (10 ft)
Three40 in.5 + 40 + 6 + 40 + 6 + 40 + 5 = 142 in.144 in. (12 ft)

The Husky roll-formed step beams we list come in 48, 96, 108, 120 and 144 in. lengths. Capacity falls as the beam gets longer: the published IBX43 beam is rated 6,270 lb per pair at 96 in. and 3,020 lb per pair at 144 in. A wider bay is not free.

Replacing existing rack?

Do not measure from the outside of the uprights. Beam length is the distance between the inside faces.

Section Three

Frame depth: how deep is the upright?

The pallet should overhang the beams front and back.

Short answer: Subtract 6 in. from the pallet depth. The pallet overhangs each beam by about 3 in.

A 48 in. deep pallet goes on a 42 in. deep frame, leaving about 3 in. of overhang at the front and 3 in. at the back. The overhang puts the pallet's stringers or runners squarely on the beams. Do not order a 48 in. frame for a 48 in. pallet.

Standard frame depths on the lines we carry are 36, 42 and 48 in. For back-to-back rows, row spacers tie the two rows together and set the gap between them. They are listed at 6, 8, 12 and 18 in. Wall ties are listed at 6, 8 and 12 in.

Section Four

Beam height and upright height

Work up from the floor one level at a time.

Short answer: Each level needs the load height, room to lift the pallet off the beam, and the height of the beam above. Beams adjust in 2 in. increments.

Level spacing

Add the loaded pallet height, a lift-off clearance and the beam profile, then round up to the next 2 in. step. The Husky step beams are published in profiles from 3.0 to 6.0 in. Example: a 6-1/2 in. pallet with 48 in. of product is 54-1/2 in. tall. With a 4.32 in. beam and, as an example allowance only, 6 in. of lift-off room, that is 54.5 + 6 + 4.32 = 64.82 in., which rounds up to 66 in. from the top of one beam to the top of the next.

Use the lift-off clearance your lift truck and your operators need. It is your number to set, not ours.

Upright height

Roll-formed uprights are listed at 96, 120, 144, 192 and 240 in. (8, 10, 12, 16 and 20 ft). The top beam does not have to be at the top of the upright, but the top load has to clear the ceiling, lights and sprinklers, and the lift truck has to reach it.

Two limits to check

  • Height to depth. The height from the floor to the top loaded beam, divided by the frame depth, should not exceed 6 to 1. A top beam at 20 ft on a 42 in. frame is 240 / 42 = 5.71, which is within the limit. At 24 ft it is 6.86, which is over.
  • Beam spacing. Upright capacity depends on the vertical distance between beams. The MECO 3 in. structural frame rating of 34,800 lb per bay applies only when beam spacing does not exceed 60 in.
Section Five

Run length and aisle width

Now fit the bays into the building.

Short answer: Run length is beam length times the number of bays, plus 3 in. per upright. Aisle width comes from the lift truck.

Run length

A row of bays has one more upright than it has bays, and each upright adds 3 in. Ten bays of 108 in. beams: (108 x 10) + (3 x 11) = 1,113 in., which is 92 ft 9 in. Measure the wall for that, less columns, doors and dock equipment.

Aisle width

The aisle is measured between the loads on either side, not between the uprights, because the pallets overhang. The right width is the right-angle stacking aisle published for your lift truck with your load size. Commonly published ranges put narrow aisle layouts at about 8-1/2 to 10 ft and very narrow aisle layouts at about 5-1/2 to 7 ft. A standard counterbalance truck needs more. Use the truck's figure, not a range.

Layout checklist
MeasureWhy
Clear height to the lowest obstructionSets the top load height
Building column locationsColumns land in flue spaces or aisles, not in bays
Doors, docks and exitsRuns cannot block egress or traffic
Floor slab and conditionEvery column is anchored to it
Section Six

Common measuring mistakes

Most rack returns trace back to one of these.

Short answer: The usual errors are measuring the pallet instead of the load, ordering frames as deep as the pallet, and forgetting the uprights in the run length.

  • Measuring the pallet, not the load. Product that overhangs the pallet sets the clearance, not the pallet.
  • Frames as deep as the pallet. Order 6 in. less than the pallet depth.
  • Forgetting the uprights. Ten bays need eleven uprights and 33 in. of floor for them.
  • Measuring to the top of the steel. Measure to the top loaded beam level, not the top of the steel, when checking height to depth.
  • Leaving out anchors and the plaque. Under ANSI MH16.1 all columns need base plates and bolted anchoring, and the rack needs a load plaque.

For rack types, capacities and standards, see our pallet racking guide. For the parts list and quantities, see pallet rack components.

Section Seven

Frequently asked questions

The questions I hear most on quote calls.

What size beam do I need for two standard pallets?

A 96 in. beam. Two 40 in. wide pallets plus 5 in. of clearance at each upright and 6 in. between the pallets comes to 96 in.

How deep should pallet rack uprights be?

About 6 in. less than the pallet depth, so the pallet overhangs each beam by about 3 in. A 48 in. deep pallet goes on a 42 in. deep frame.

How do I calculate pallet rack run length?

Multiply the beam length by the number of bays and add 3 in. for each upright. Ten bays of 108 in. beams need 1,113 in., or 92 ft 9 in.

How much space do I need between beam levels?

Add the loaded pallet height, the clearance your lift truck needs to lift the pallet off the beam, and the height of the beam above. Then round up to the next 2 in. adjustment step.

How wide should pallet rack aisles be?

As wide as the right-angle stacking aisle published for your lift truck with your load. Commonly published ranges are about 8-1/2 to 10 ft for narrow aisle layouts and about 5-1/2 to 7 ft for very narrow aisle layouts.

How tall can pallet racking be for its depth?

The common rule is a maximum height to depth ratio of 6 to 1, measured to the top loaded beam level. On a 42 in. frame that is a top beam at 21 ft.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting pallet racking, uprights, step beams and accessories and wire decking.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Want us to check your measurements?

Send us your pallet size, load weight, clear ceiling height and lift truck model, and we will lay out the bays. Quote requests are answered within 24 hours by a real person.

866-333-0728

Browse pallet racking at custommhs.com

Browse pallet rack components

Get a fast quote

No bots. No guesswork. Real experts.

Specification sources

CustomMHS pallet racking and pallet rack components guides and Husky and MECO listings · ANSI MH16.1 and RMI published guidance · published dealer measuring guidance for clearances.

Published figures are current as of November 2026 and are subject to change by the manufacturer. This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.