Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

What Is a Driver Cage? Controlling Dock Door Access Without Slowing Deliveries

A driver cage is a small wire enclosure just inside a dock or entry door. Drivers and vendors come in, check in and wait there, and go no further.

Written and reviewed by: Tom McGovernPublished: November 2026Covers: WireCrafters driver and building access cagesQuestions: 866-333-0728
Section One

What is a driver cage?

Also called a building access cage or dock door security cage.

Short answer: A driver cage is a wire mesh enclosure built around the inside of a personnel or dock door. It lets drivers and vendors enter the building and hand over paperwork while keeping them out of forklift lanes and away from inventory.

Quick answers
  • What it does: Keeps visitors out of forklift traffic and away from stock, and gives you one place to check credentials.
  • Why it does not slow deliveries: A service window with a shelf lets paperwork pass through, so the driver never has to leave the cage.
  • Sizes: From 3 ft 4 in. square up to 8 ft 6 in. x 8 ft 4 in.
  • Layouts: Two-wall for a corner, three-wall against a flat wall.

Without a cage, the door a driver walks through opens straight onto your floor. With one, the driver is inside, out of the weather, and visible, and the next door is one your staff controls.

A note on this guide

This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.

Section Two

How it works at the door

Three parts do the job.

Short answer: The cage surrounds the entry door. A service window handles paperwork. A second, staff-controlled door leads into the building.

The enclosure

Wire walls around the entry door

Built from the same heavy duty wire partition system as a security cage. Open mesh keeps the driver visible and lets light and air through.

The service window

With a shelf for paperwork

Bills of lading and signatures pass through the window. Your receiving clerk stays on the warehouse side.

The inner door

Hinged, 3 or 4 ft wide

A pedestrian door for staff access, locked from the warehouse side. A Dutch door pass-through is also published as an option.

Benches are available so drivers can sit while they wait: the MTB-4, MTB-6 and MTB-8 are 4, 6 and 8 ft long.

Section Three

Sizes and models

The model number tells you the layout and the size.

Short answer: MT2 is a two-wall cage and MT3 is a three-wall cage. The two digits are width and depth in feet.

Driver cage models
ModelLayoutSize
MT2-33HD2-wall3 ft 4 in. x 3 ft 4 in.
MT3-33HD3-wall3 ft 4 in. x 3 ft 4 in.
MT2-46HD2-wall4 ft 4 in. x 6 ft 4 in.
MT3-56HD3-wall5 ft 6 in. x 6 ft 4 in.
MT2-88HD2-wall8 ft 6 in. x 8 ft 4 in.
MT3-88HD3-wall8 ft 6 in. x 8 ft 4 in.

Published widths are 3 ft 4 in., 4 ft 4 in., 5 ft 6 in., 6 ft 6 in., 7 ft 6 in. and 8 ft 6 in. Depths are 3 ft 4 in., 4 ft 4 in., 6 ft 4 in. and 8 ft 4 in. The 3 ft 4 in. wide cage takes a 3 ft hinged door. All the others take a 4 ft door.

Worked example: floor area

The smallest cage is 3 ft 4 in. square. That is 3.33 x 3.33 = about 11 sq ft, room for one person standing. The largest is 8 ft 6 in. x 8 ft 4 in., which is 8.5 x 8.33 = about 71 sq ft, more than six times the floor area. Price rises much more slowly than floor area, so if several drivers arrive together, the larger cage is good value.

Section Four

Two-wall or three-wall?

It depends on where the door is.

Short answer: A two-wall cage fits a door near a corner and uses two building walls. A three-wall cage fits a door in the middle of a wall.

Layout by door location
Door locationCageBuilding walls used
Near an inside corner2-wall (MT2)Two
In the middle of a flat wall3-wall (MT3)One

The two-wall cage has fewer panels, so it costs less for the same floor area. If you are laying out a new dock office or moving a door, putting the visitor entrance near a corner saves money on the cage.

Section Five

Choosing the size

Count the people and what they do while they wait.

Short answer: Size the cage for the most drivers who wait at the same time, plus a bench if waits are long.

One driver at a time, quick paperwork
3 ft 4 in. square, two-wall or three-wall.
Two drivers, or one with a hand truck
4 ft 4 in. x 6 ft 4 in. or 5 ft 6 in. x 6 ft 4 in.
Several drivers, or long waits
8 ft 6 in. x 8 ft 4 in. with a bench.
Door near a corner
MT2 two-wall.
Door in a flat wall
MT3 three-wall.
Staff also use this door
Add a coded or card lock on the inner door so staff pass through without a key.
A space that does not match a standard size
Build it from standard partition panels. See our WireCrafters Style 840 guide.
Section Six

Common mistakes

Check these before you order.

Short answer: The usual errors are undersizing the cage and forgetting about exit requirements.

  • Sizing for one driver when three arrive together. A cage that holds one person backs the rest up outside.
  • Blocking an exit. The cage sits in an exit path. Check egress requirements with whoever handles your building code compliance before you lock an inner door.
  • Service window on the wrong side. Put the window where the clerk already works.
  • Not checking the floor. Panels mount to the floor with supplied concrete anchors. Uneven slabs need attention at installation.
  • Expecting the cage to replace a process. A cage controls where visitors go. It still needs a procedure for who lets them in.

See also how much a wire security cage costs and our wire partitions and security cages guide.

Section Seven

Frequently asked questions

The questions I hear most on quote calls.

What is a driver cage?

A driver cage is a wire mesh enclosure built around the inside of a dock or entry door. Drivers and vendors can enter and hand over paperwork without getting access to the warehouse floor.

Why do warehouses use driver cages?

To keep drivers and vendors out of forklift lanes and away from inventory, and to give one controlled place to check credentials.

What sizes do driver cages come in?

WireCrafters driver cages run from 3 ft 4 in. square up to 8 ft 6 in. x 8 ft 4 in., in two-wall and three-wall layouts.

What is the difference between a two-wall and a three-wall driver cage?

A two-wall cage fits in a corner and uses two building walls. A three-wall cage sits against one flat wall.

Does a driver cage slow down deliveries?

It should not. A service window with a shelf lets paperwork pass through while the driver stays in the cage.

Can drivers sit down in a driver cage?

Yes. Benches are available in 4, 6 and 8 ft lengths.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting WireCrafters driver and building access cages.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Need a driver cage sized for your door?

Tell us the door location, how many drivers wait at once and where your receiving desk is, and we will recommend a model. Quote requests are answered within 24 hours by a real person.

866-333-0728

Browse driver and building access cages at custommhs.com

Get a fast quote

No bots. No guesswork. Real experts.

Specification sources

CustomMHS wire partitions guide, WireCrafters Style 840 guide and driver cage listings · WireCrafters published specifications.

Published figures are current as of November 2026 and are subject to change by the manufacturer. This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.